Just Another Type 3 Blog

 
 
 
     
    April 21, 2003

    Chewed Gland Nut Wife and I went to a beautiful suburb of Philadelphia today to pick up a new engine and transmission for the Square. The Transmission is going up to my parents’ house in New Hampshire until I (hopefully never) need it, or until we get our house another year or so from now. The transmission is an automatic out of a marina blue 71, just like mine. The engine was out of the same car, which had been converted to carbs (the pain!)… I’ll have to check the engine number and see if it’s at all close to mine. The car had been abandoned on the streets of Philly and was sold by the city for spare parts because it had no title. At least that’s what the guy who bought it told me. I guess you can’t get a title for an abandoned car? Anyway, it looks like it had been left there because the pulley had sheared off the crankshaft. Yipes. It also looks like someone had a go-around with the gland nut on the other side. I guess I’ll start tearing this one apart on my vacation next week. Hopefully just about everything is good inside and I can rebuild it to get a few more thousand miles from it. I’m going to be doing this on my deck, so it should be lots of fun. (ugh) When we get our house I will, of course, be revisiting this, but hopefully this will get me going until then. Will probably need a new crankshaft. Once I replace this motor, I will probably disassemble the one currently in the car to see what’s going on with that bad cylinder (I imagine I will not have to go far to find out). What an adventure this is turning out to be!

    Comments Off on April 21, 2003
    April 20, 2003

    Decided to actually pull the back of the car out of the garage to double-check the valves and torque down the lower part of the heads to see if that was causing my low compression reading on cylinder #3. I realized when I tried to check the valves on Thursday night that I had the engine in the complete wrong position. For some reason I hadn’t been able to see the notch in the distributor that signified cylinder #1. I left Thursday night thinking I had done something very wrong, and a couple people on the Type 3 list mentioned that I must have had the engine turned 360 degrees incorrectly if I couldn’t adjust the valves. That’s exactly what had happened. So I turned the engine over to where it should be for cylinder #3 and took the valve cover off, removed the rocker arms and checked the torque on the heads. They were way loose and I was hoping this was my problem. Put the rocker arms back on, torqued them up, did a complete valve adjustment, then did the compression test. I gained 10psi on cylinder #3, but that still only brought it to 60psi, which means either way I’m going to have to pull the engine out. Decided *not* to do that today. Instead, I jacked up the front of the car to get a good look at the underneath of the gas tank & to replace the fuel lines in the front. I discovered a little canister on the front of the torsion bar beam and didn’t know what it was. It went to the pressure outlet of the fuel pump and then to a line in the tunnel. A few posts on the Type 3 list noted that this was a “fuel muffler,” and that most cars either had it removed by now, or could have it removed. I decided to leave it on though and replaced its fuel hoses. The only one I did not do was the one from the three-way plastic plug to the tank itself. I was going to put a long hose on that one so the tank would be easier to take out if and when necessary, but Jim Adney suggested that I leave the tank because it’s tough to seal it up sometimes after you get it out. I’m leaving it. I took the fuel pump with me because I wanted to take it apart, but knowing how much it costs, I think I’ll leave the taking apart for when I have some more cash (or until I it actually fails) in case I futz it up. I do need to get at least one new mounting bracket for the pump though, as it looks like the rubber sheared off from the clamp that holds the pump. The pump was just kind of “resting” on the bushing. Also replaced the fuel filter as well.

    Comments Off on April 20, 2003
    April 16, 2003

    Another beautiful night last night, and my wife was in Manhattan with my stepson attending an open house at a school for holistic medicine, so I figured I’d stop by the car on my way home & finally do the compression check. Got all the plugs out and screwed in the plug for the tester. Took all the wires off the distributor cap as I needed to sort out the order anyway, and I have a new set coming from Aircooled.net. Got in the car, turned the key for a couple seconds & went back to take a look at the gauge. 120psi. Much better than I had hoped for. Took the hose and adapter out of cylinder 2 and did cylinder 1. 128psi. Nice. Got to cylinder 3. 50psi. Yipes. Did cylinder 4, 120psi and then went back to cylinder 3 to check it again. Again, 50psi. Not good. At this point I was thinking it was most likely valve related, as I didn’t think the rings could be that far gone on only one cylinder. It started raining so I packed up & went home, trying to figure out what to do next. A couple people on the Type3 list said I should check my valve adjustment (will do that tonight or Saturday) and Russ mentioned that there’s a chance that a piece of carbon might be caught in the valve keeping it from sealing shut.

    Comments Off on April 16, 2003
    April 15, 2003

    Gas Tank I had grand ambitions tonight, but ended up doing just a few things. I was glad to see the battery was still fine and that I didn’t have any mysterious drainage from anything. However, I realized the clock actually didn’t work. It ticks, but it doesn’t keep time. Not a priority in any case. As recommended by Jim Adney off the type 3 list, I checked the starter terminal connections to see if they were mixed up, as that could be causing the problem where I don’t hear the fuel pump relay clicking off after a second or two of the ignition being on and the car not starting. Wires were on the correct terminals but there was a lot of corrosion on the red/white terminal. Cleaned it off a bit and wondered why there wasn’t a plastic boot on it to protect it from the elements. I had been wanting to check the trigger points in the distributor, so I finally loosened the adjustment screw and got the distributor out. Pulled out the trigger points module and everything in there was very clean. I took whatever little gunk was off the plastic tabs that hit the distributor cam lobes, put just a dab of lube on the cam and put the points back in. Sometime during this operation, a couple plug wires came off the distributor cap. Damn. Decided to order a new set & just make sure everything is rewired properly when I put the new wire set on. Old ones were questionable anyway.

    Also, in my first most embarrassing moment, I realized that the gas tank is most likely empty. The Muir book says to watch out for this, but did I pay attention to that? Nope. Turned the key and for the first time watched the gas gauge go… NOWHERE. Got out and pushed on the side of the car with the hood open to see if I could hear any sloshing. Nothing. I figure now would be a good time to change all my fuel lines. I’ll take care of that Saturday before putting any gasoline in the tank. It probably might not be a bad idea to check the status of the tank as well. Listened to a little bit of the Bruins game 4 on the Wolfsburg radio. Sweet.

    Comments Off on April 15, 2003
    April 12, 2003

    Frayed Wires Vacuumed out the baking soda I had left covering the battery area as well as the other side of the rear seat. I noticed that there was a yellow with red stripe wire that had been taped off with electrical tape coming from the positive side of the battery connection. I looked it up in the Bentley manual wiring diagram and I believe it just went to the computer connection that VW used to check the engine and electrical system. It was probably used to check the condition of the battery. Looked like it would’ve connected to an older stock battery?

    Anyway, I also found by the voltage regulator on the other side that several wires were frayed and uncovered. It looked like someone had tried to splice them together and didn’t do a very good job at it. I don’t think I have any leeway in cutting them down and resplicing them though because they’re in there pretty tight and it’s a hard place to get at. I’ll have to find out what each connection is for and then figure out if it’s causing the car not to start, or if it will provide problems later on. Could very well be a ground to something. Interestingly enough, this battery is shorter than the one I pulled out and has a positive terminal cap to prevent shorting out on the seat springs. The Interstate battery it replaced did not have a cover and was most likely tall enough to hit the seat springs. Wonder what kind of hell that could’ve caused?

    After the battery was in, I replaced the points (heavily pitted) and condenser, set the point gap, lubed the distributor cam and popped the cap back on. Decided to see if the pitted points were stopping the engine from running. Turned on the ignition and nothing but the first “click” and the hum of something in back of me (fuel pressuring up?). Also, the oil and generator lights went on. Turned on radio. It worked. Horn worked too. Before I started suspecting a starter problem, I took the car out of park and put it into neutral, then tried again. Car turned over, but didn’t start. OK, so much for me taking the lazy way out. Changed the spark plugs and was VERY happy I had picked up one of those double-jointed elbow sockets on the way over because it made the job not only easier, but possible.

    Plugs were covered in soot, but were not oily. Engine must have been running rich, but my previous thought that the compression might be bad might not have been entirely accurate as there was no sign of oil on the plugs. Of course, the one thing I was supposed to get on the way over — a compression tester — was the one thing I totally forgot about when I stopped at Pep Boys. I did pick up one of those lighted telescoping magnets though, which came in infinitely handy when trying to put the condenser hold-down screw in. Another weird thing — the new condenser goes in upside-down. Only way I could get it in, and the way the new bracket is attached it looks like it’s meant to be that way.

    Lost the rubber gasket from inside my spark plug socket on #3 cylinder. Popped it off the plug but it’s now stuck under the engine tin. I couldn’t get to it with my fingers, but I’ll have to try again tomorrow when I go back to do some fuel injection troubleshooting. Didn’t put any anti-seize on the plug threads either, which I don’t necessarily think is a bad thing. Aircooled.net says use milk of magnesia, but I had none available, so I put them in dry. Looks like the old ones were put in dry as well, so I’m not worried.

    Tried to start the engine quickly again, and no dice. I know the type3 list talks about two clicks you should hear from the fuel injection system — one when you turn the key, then another one a second or two later. I don’t hear the second one. Will have to find out what the second one is for. Looked through the Muir book when I got home and found out it has a pretty decent troubleshooting section on getting the Type3 FI engine started. I guess I’ll start going over that from start to finish — going to set the valves, then check for spark & fuel & all the stuff it suggests. I am a bit worried that Muir says 100K is the top of the life expectancy of this engine, but hopefully when I do finally get a compression tester on it the results won’t be horrible.

    Discovered the timing marks on the crank pulley are for 0, 5, 7.5 and 10 degrees BTDC. Static timing is set to 0 degrees, but the Bentley says timing should be set with a strobe, so I’ll do that after I get the engine running. Zero degrees should be good to start with I think. Also realized that the gas tank filler door does not open. Guess I’ll have to find a way around that. So I guess the goal right now is to get the engine started. Once it starts, I’ll get to replacing fuel lines and other stuff before it’s actually driven anywhere. I’m trying not to let anything else distract me too much.

    Comments Off on April 12, 2003